#Cisco console port configuration password

You can enable the Reset button feature on the device only under any of these scenarios: Service password-recovery command, and to disable the feature, use either the no service password-recovery command or the no service password-recovery strict command.

#Cisco console port configuration password

In the Next article ,we will see that how we can scan the chassis using the UCS Manager.To enable the Reset button functionality on these devices, configure the device with the password recovery service using the Once the UCS manager is launched, you need to configure certern polices to scan the chassis.В Hope this article is informative to you. Launch the UCS manager using the cluster IP. Continue (y/n) ? yД®nter the admin password of the peer Fabric interconnect: passwordДЄpply and save the configuration (select вЂnoвЂ™ if you want to re-enter)? (yes/no): yesД«oth Fabric Interconnects should now be configured with basic IP and Cluster IP information.ДҐ. This Fabric interconnect will be added to the cluster. Installer has detected the presence of a peer Fabric interconnect. Once again, you need to follow like below. Now connect to the console port of the secondary FI and power it on. IPv4 address of the default gateway : X.X.X.XД¬luster IPv4 address : X.X.X.X (NOTE: This IP address will be used for Management)Д¬onfigure the DNS Server IPv4 address? (yes/no) : yД¬onfigure the default domain name? (yes/no) : yДefault domain name: Apply and save the configuration (select вЂnoвЂ™ if you want to re-enter)? (yes/no): yes Physical Switch Mgmt0 IPv4 netmask : X.X.X.X Physical Switch Mgmt0 IPv4 address : X.X.X.X Is this Fabric interconnect part of a cluster(select вЂnoвЂ™ for standalone)? (yes/no) : yes Continue? (y/n): yД¬onfirm the password for вЂњadminвЂќ: password Setup You have chosen to setup a new Fabric interconnect. (console/gui) ? consoleД®nter the setup mode setup newly or restore from backup. Once you have connected to the FI вЂ“ A management console, you will get the interactive session like below. Verify that the console port parameters on the attached computer are as follows вЂњ9600 baudвЂќ, вЂњ8 data bitsвЂќ, вЂњNo parityвЂќ, вЂњ1 stop bitвЂќ. Power on FI-A and leave the secondary FI off for now. UCS complete environmentДЄt this point, you have physically setup the UCS environment.Д¬onnect to the consoleВ port of Fabric Interconnect (FI) вЂњAвЂќ, which will be the primary member of the cluster. This Nexus switch has capability to diverging the LAN & SAN traffic to theВ peer devices. L1 & L2 ports provides the connectivity between two FIвЂ™s. So that chassis can be discovered in the UCS manager. Laid the cabling between the chassis and Fabric interconnect. L1 & L2 ports are used for Fabric interconnect heart-beating and this connectivity ensuresВ that both the FIвЂ™s maintaining the identical data.Дў. Connect the L1 port of Fabric Interconnect вЂњAвЂќ to the L1 port of fabric interconnect вЂњBвЂќ. The Fabric interconnectвЂ™s MGMT port needs to be connected to theВ management network. You need to interconnect the FIвЂ™s to make the FI cluster. Setup theВ Fabric Interconnect (UCS Manager). So that both the FIвЂ™s configuration will be sync with each other.ДЎ. There will be a dedicated ports to provide the connectivity between FIвЂ™s. Fabric interconnect has its own management ports to manage it. Unlike the traditional chassis, Cisco UCS have additional components like I/O modules (FEX) and Fabric interconnects (FI / UCS Manager). The core part of CiscoВ UCS deployment is cabling. Cisco UCS is highly customizable and the configuration will be differ for each environment. This article will provide the step by step instructions to setup the Cisco UCS environment for first time.